ARMAGUARD RUST PROTECTION OXIDE RED
ARMAGUARD is a high-performance epoxy paint characterized by its polyamide curing, high solids content, and excellent durability. Here are the key details about this product:
Armaguard sold as Component A Colour, Component B Hardener and thinners or as Kits containing all components and Thinners plus 5 Mixing Cups, 3 Paint Stirrers, 1ltr Panel Wipe.
Key Characteristics:
- Polyamide Curing: Ensures a strong, chemical-resistant bond.
- High Solids Epoxy: Provides a thick, robust coating that minimizes the number of coats needed.
- Hard and Tough Coating: Results in a durable surface that withstands physical and chemical stress.
- Good Wetting Properties: Enhances adhesion to various substrates, including those with minimal surface preparation.
- Low Temperature Curing: Capable of curing at lower temperatures, making it versatile for different environments.
- Non-Porous: Will not allow the transfer of moisture through the paint film.
- 3:1 Mix Ratio: Simple to mix and easy to apply.
| Product description | 2 pack modified Polyamide curing high build epoxy rust proofing paint. |
| Coverage & Pack description | 6.4Sq Mtr Per Litre coverage.1.00ltr 1ltr can filled with 750ml Comp A, 500ml can filled with 250ml Comp B
1.25ltr starter pack 1ltr can filled with 750ml Comp A, 500ml can filled with 250ml Comp B & 250ml Armaguard Thinner 2.00ltr 2x 1ltr can filled with 750ml Comp A, 2x 500ml can filled with 250ml Comp B 2.25ltr chassis pack 2x 1ltr can filled with 750ml Comp A, 2x 500ml can filled with 250ml Comp B & 250ml thinner. 5ltr pack 1x5ltr can filled with 3.75ltr Comp A, 1×2.5ltr Can filled with 1.75ltr Comp B. 6ltr pack 1x5ltr can filled with 3.75ltr Comp A, 1×2.5ltr Can filled with 1.75ltr Comp B. & 1ltr thinner. 6ltr custom-made colour pack 1x5ltr can filled with 3ltr Comp A, 1×2.5ltr Can filled with 2ltr Comp B. & 1ltr thinner. |
| Application temperature | Can be applied to steel as low as 0c. The steel must be at least 3 degrees above the current dew point. (See our dew point calculator.) |
| Thinning | Use only the Armaguard Thinner supplied, from 5 to 20% max. |
| Application & recoating | Brush or spray. A second coat or topcoat can be applied any time after approx. 5 hours* with no need to abrade between coats. If recoating or top coating once the first coat has fully cured (after approx. 7 days), lightly abrade first with P320 paper.* At 20 degrees centigrade. Longer interval may be required in colder conditions. |
| Spraying & Cleaning | Minimum 1.8mm nozzle or a HB (high build) primer set up. Test atomisation on a test panel first. Viscosity will vary, i.e. thicker in colder temperatures. Data correct at 20c.Conventional Spray (Air) 3-4bar – 44-58psiAirless Spray 18thou tip, 150bar – 2176psi
Clean up with standard thinner or gun wash. Do not thin the paint with standard thinner as this will affect the paint cure. |
| Pot life | Pot life is the time from mixing the two components together to the point at which the mixed paint is no longer useable. For EM121, you have 90 minutes pot life once mixed at 20c – longer at colder temperatures. |
| Shelf life & Storage | We recommend storing upside down in a dry place at around 20c. In these conditions the product has a shelf life of 12 months. Do not store below 20c as this can affect performance. |
| Disposal | Allow any excess mixed paint to cure in your mixing cup and throw away as dry waste. |
| Mix Ratio | 3 Parts Component A to 1 Part Component B (3:1) |
| Safety | Use in a well-ventilated atmosphere. Use a respirator face mask when spraying or brushing in an enclosed space. Please see the MSDS (material safety data sheet) in our data sheet area.Wear suitable protective clothing, gloves and eye protection. |
