Injecting your vehicle with cavity wax.

Injecting your vehicle with cavity wax.

Tuesday 8 February 2022


Injecting your vehicle with cavity wax.

Cavity waxes are specially manufactured fluid waxes to inhibit rust and waterproof the insides of vehicle box sections, Lanolin based rustproofing solutions also have the benefit of hermetically sealing the surface from oxygen. But why do we need to rustproof these areas?

The rust that forms within a crevice or seam within a hidden cavity can corrode at up to 400 times faster than corrosion on open surfaces, once humidity enters the oxygen starved crevice this rate of corrosion is just about guaranteed. Soaking these cavities in a penetrating fluid and cavity wax is simply necessary but with a word of caution,

A poorly injected cavity could rust more than one that has not been injected at all. How?

The un-coated steel within the cavity has a greater potential to rust than the coated steel around it due to all of the electrolytic action being focused on these bare spots. Poor injection equipment and particularly finger operated pumps will not atomise the wax sufficiently and you will get uncoated spots (holidays) within the coating.

You will get similar results using a wax that does not flow or is not easily atomised.

If you have to thin a wax then the final barrier film thickness will be reduced by the amount of thinner you add , 30% white spirit will reduce your dry film thickness by 30%. Heating the wax allows the product to naturally reduce in viscosity and when cool it will re-thicken, using correct equipment will give you good penetration and a good film thickness, perfect for cavity injection.

So how do I inject the cavities of my vehicle?

The professional Wax Injection kit from Rustbuster comes with ,

  • Quality spray gun.
  • Sturdy metal cup.
  • 800mm x 360 degree cavity wax injection wand.
  • Hook spray wand for spraying cavity wax in a fan pattern at 90 degrees.
  • A specially manufactured Rustbuster bullet tip for fine spraying of higher build underbody waxes.

For injection of the cavities, we are going to focus our attention on the  800mmx 360° Injection Wand. And for the purposes of this blog, we will also assume your chosen cavity wax has been heated to a minimum 40°c, you have a suitable compressor running 6-8cfm and 60-90psi.

 

/cavity blog__resized.jpg

 

You will see in the image above a number of underbody cavity access points, this will allow the 360° injection wand access. Push the wand in to the cavity access point in the direct of the cavity, try to push this in as far as possible. Whilst triggering the spray gun slowly pull the probe out of the cavity this will then allow the internal of the cavity to all be coated in atomised warmed wax. If you have injected the cavity with enough wax, you will see it visibly coming out of the probe exit point when full withdrawn.

/rob injecting.JPG

People often ask how quickly I should pull the probe from the cavity and it’s not really a question you can answer with a speed, but you should be getting enough cavity wax inside for it to actually be beneficial. For instance, on a MGB you might use 2/3ltr across the underside cavities, doors, bonnet, boot for a Land rover 110 you may use 4/5ltr as it’s a lot bigger, has a lot more cavities and requires special attention in key areas known to rot bulkhead)

All underside cavities will need to be injected and the key ones are quite obvious as they are easily visible. Any hollow area on the vehicle is to be coated. Please see the drawing below,

This injection drawing from Dinitrol provides a guide of all required injection points on this MGB. We may have a drawing like this for your vehicle, please enquire and we'll ship with your order.

 

/cavity wax 123.JPG                                                                                                                                                        

Rustbuster supply many cavity waxes and penetrators,

These products can be found rust proofing kits, aerosol, 1ltr schutz cans or larger.

If you require any further information, injection drawings is available or advice please don’t hesitate to contact us. We also may have an approved rust proofing specialist near you.

 

Share This Article



Contact Rust


Rustbuster Ltd
Welland House
Cradge Bank
Spalding
South Lincolnshire
England
PE11 3AN

01775 761 222

sales@rust.co.uk

Social Media



Rustbuster is a registered trade mark of Rustbuster Ltd, registered in the UK Trademark number 2211446 Class 02 & 37.
Any unlawful use of the Rustbuster name or logo or passing off will result in legal proceedings. Rustbuster Ltd UK registerered 3639350.