COATING AREAS WITH EM121 EPOXY MASTIC

 

EM121 Epoxy is a high build, high solids two pack (has a base and hardener) Epoxy paint coating for the renovation and protection of rusting and pitted steel exposed to severe environments. EM121 Epoxy can be applied successfully over wire brush cleaned steel and still offers the same exceptional performance as coatings applied over blast cleaned steel. Its finish is as hard as iron but flexes with the steel. See photos at the foot of this page of a customer’s VW restoration.

EM121 Epoxy  will not flake, peel or blister - even under water. Resists oils, salt water and mechanical damage. Tough penetrating coating that is more flexible than the steel itself. Has six times the penetration and adhesion of single pack products. Does not contain any harmful isocyanates. It will resist temperatures of up to 200c before discolouration, and 350c before blistering.

 

Available in twelve standard colours or custom made in RAL or BS standard colours.

THE BEST WAY TO USE EPOXY MASTIC 121

 

Mixing

Epoxy 121 is a two-pack modified epoxy high build coating.

Comprising of base colour component, A, and an equal amount of hardener component B.

Mix components A and B together in equal amounts i.e. 100ml A to 100 ml B by measure. Allow to stand for approximately ten minutes to allow the chemical process to start.

All of the data on our technical data sheets are calculated at 23 degrees C if the ambient temperature causes the Epoxy 121 to be a higher temperature the product will be thinner. At low temperatures 8 degrees c the product will be much thicker almost paste like.

Thinning

Epoxy 121 can be thinned up to a maximum of 15 – 20% with the thinners provided in each kit. For spraying or fine brushing, you will definitely need the thinner.

" Top Tip" As a surface filler

Without thinning EM121 can be used as a filler coat for imperfections on steel surfaces of up to .5 of a ml thick ( 500 um/microns) by mixing equal amounts of component A and component B without adding any thinner, allow to stand for ten minutes and then brush onto surface and scrape away excess to level the surface.

For Brushing

Depending on the temperature at the time of application Epoxy 121 can be easily brush painted. The addition of up to 15% of the thinners supplied may be added. Use a fully loaded wet brush and long strokes for the best finish.

By Roller

Epoxy 121 can be applied by roller, load the roller up fully before applying to the surface.

Roller application requires twice the number of coats to eradicate the chance of any misses ( holidays) in the coating.

By Air Spray

Use a spray gun with a 1.8 tip size smaller tips can be used on gravity fed spray guns. Thin the product up to 15% with the thinners provided.

Over painting

Epoxy 121 can be overpainted with any paint product. If fully cured ( over two weeks) a light sanding with a 320 grit abrasive will be required prior to painting.

Seam sealing

Apply Epoxy 121 to the bare steel area first, A seam sealer preferably polyurethane can then be applied over the epoxy 121 to seal the seam.

Filling over EM 121

Due to the very hard nature of Epoxy 121 when cured we would recommend a sanding with an 80 grit and filling with Epoxy paste PC-7.

Protect your precious metal

GET THE LATEST NEWS AND OFFERS




Information


Blog

Contact Us

Sitemap

Contact Rust


Rustbuster Ltd
Welland House
Cradge Bank
Spalding
South Linconshire
England
PE11 3AN

01775 761 222

sales@rust.co.uk

Social Media



Rustbuster is a registered trade mark of Rustbuster Ltd, registered in the UK Trademark number 2211446 Class 02 & 37.
Any unlawful use of the Rustbuster name or logo or passing off will result in legal proceedings. Rustbuster Ltd UK registerered 3639350.